Телефон: +7 (937) 519-34-24

DOWNLOAD- PDF Tech Sheet

Use to connect up to 14 LEDs directly to the throttle and auxiliary channels of the RX (receiver) using the included RX Pass-Thru™ with dual intensity brake light action and auxiliary channel switching built right in.

Pins can be soldered to for a hardwired connection. Pins can also be removed if they will not used.

Plug the DELUXBRAKE™ 14 LED Controller into the throttle and auxiliary channels of the RX by plugging the 2-channel RX plug into either set of PWR & AUX channels on the LED controller with the rib UP.  Plug the connector with 3 wires on the other end into the RX Pass-Thru™ along with the throttle servo or ESC; and then into the RX throttle channel.  Then plug the connector with 1 wire into the RX auxiliary channel tied to the two-position switch on the TX that you want to use.

If a separate power source (3.6-7.4VDC) will be used, follow these instructions.

Align BLUE wires with the top side of the DELUXBRAKE™ 14 LED Controller. DELUXBRAKE 14 LED Controller Installed

LED CONTROLLER BANKS

1 LB1, LB2, RB1, RB2 : BRAKE LIGHTS

2 LH1, LH2 : HEADLIGHTS (LEFT)

3 RH1, RH2 : HEADLIGHTS (RIGHT)

4 LA1, LA2 : AUXILIARY (LEFT)

5 RA1, RA2 : AUXILIARY (RIGHT)

6 LFG, RFG : FOG LIGHTS

LED CONTROLLER CHANNELS

PWR 3.6-7.4VDC POWER INPUT

AUX THROTTLE SIGNAL INPUT USED TO SWITCH LB & RB LED CHANNELS DIM / FULL BRIGHT & AUXILIARY SIGNAL INPUT USED TO SWITCH POWER ON/OFF TO HEAD-TAIL / HEAD-AUX-FOG-TAIL (top pin auxiliary signal, bottom pin throttle signal)

LB1, LB2, RB1, RB2 CONSTANTLY DRIVE ANY SINGLE LED, ALL LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL BE DIM UNLESS THROTTLE SIGNAL INDICATES BRAKES; IN WHICH CASE LEDs ARE FULL BRIGHT. (LED BANK 1)

LH1, LH2, RH1, RH2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LEFT LED CHANNELS ARE THE SAME, AS ARE BOTH RIGHT LED CHANNELS, BOTH BANKS OF LEDs WILL BE CONSTANT ON UNLESS HEAD STROBE (OPTION SELECT DIP SWITCH HS) IS ENABLED, IN WHICH CASE THE HEADLIGHTS WILL STROBE BETWEEN THE RIGHT AND LEFT BANKS. STROBE RATE CAN BE ADJUSTED USING ADJUSTMENT POT P1. (LED BANK 2 & 3)

LA1, LA2, RA1, RA2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LEFT LED CHANNELS ARE THE SAME, AS ARE BOTH RIGHT LED CHANNELS, BOTH BANKS OF LEDs WILL BE CONSTANT ON UNLESS AUXILIARY SIGNAL INDICATES OFF. (LED BANK 4 & 5)

LFG, RFG CONSTANTLY DRIVE ANY SINGLE LED, BOTH CHANNELS ARE EXACTLY THE SAME, CONSTANT ON AT INTENSITY DETERMINED BY ADJUSTMENT POT P2 UNLESS AUXILIARY SIGNAL INDICATES OFF. (LED BANK 6)

DELUXBRAKE 14 LED Controller RX Pass-Thru

LED CONTROLLER OPTION SELECTION DIP SWITCHES

BL BRAKE LIGHTS : Brake lights dim/full intensity at center-stick (choose if brake lights are on or off at idle)

HS HEAD STROBE : Headlight strobe on/off (choose if headlights strobe or are constant on)

TR THROTTLE REVERSE : Reverses the throttle signal input (if brake lights turn on with gas then flip this switch)

C3 CHANNEL 3 : Determines if auxiliary channel is single or multi-mode (choose if auxiliary channel turns everything on/off or if it turn headlights and brake lights on with one flip, and everything on with another)

LED CONTROLLER ADJUSTMENT POTS

P1 HEAD RATE : Headlight strobe speed (if enabled with option select DIP switch HS)

P2 FG INTSY : Fog light intensity (dim to full-bright)

PINOUT LEGEND

RESISTOR RESISTOR IN CIRCUITRY

CONNECTION ELECTRICALLY CONNECTED

IC INTEGRATED CIRCUIT

DELUXBRAKE 14 LED Controller

+ POSITIVE VOLTAGE FROM POWER SOURCE

- NEGATIVE GROUND FROM POWER SOURCE

R+ POSITIVE OUTPUT WITH INLINE RESISTOR

T- NEGATIVE BRAKE LIGHT OUTPUT (THROTTLE SIGNAL SWITCHED)

A- NEGATIVE AUXILIARY LIGHT OUTPUT (AUXILIARY SIGNAL SWITCHED)

H- NEGATIVE HEADLIGHT OUTPUT (HS DIP SWITCHED)

F- NEGATIVE FOG LIGHT OUTPUT (P2 DETERMINES INTENSITY)

T THROTTLE SIGNAL INPUT

A AUXILIARY SIGNAL INPUT

TOP PINOUT

5053 Top Pinout 

BOTTOM PINOUT

5053 Bottom Pinout

WIRE COLOR (TO RX)

BLUE - POSITIVE (TOP PWR PIN ON LED CONTROLLER)
BLACK - GROUND (BOTTOM PWR PIN ON LED CONTROLLER)
WHITE - THROTTLE SIGNAL (BOTTOM AUX PIN ON LED CONTROLLER)
GREY - AUXILIARY SIGNAL (TOP AUX PIN ON LED CONTROLLER) 

WIRE COLOR (TO LEDs)

BLUE - POSITIVE
BLACK - GROUND