Телефон: +7 (937) 519-34-24

DOWNLOAD- PDF Tech Sheet

Use to connect up to 14 LEDs directly to the throttle and auxiliary channels of the RX (receiver) using the included RX Pass-Thru™ with dual intensity brake light action and police strobe light action built right in.

Pins can be soldered to for a hardwired connection. Pins can also be removed if they will not used.

Plug the 911STROBE™ 14 LED Controller into the throttle and auxiliary channels of the RX by plugging the 2-channel RX plug into either set of PWR & AUX channels on the LED controller with the rib UP.  Plug the connector with 3 wires on the other end into a RX Pass-Thru™ along with the throttle servo or ESC; and then into the RX throttle channel.  Then plug the connector with 1 wire into the RX auxiliary channel tied to the two-position switch on the TX that you want to use.

If a separate power source (3.6-7.4VDC) will be used, follow these instructions.

Align BLUE wires with the top side of the 911STROBE™ 14 LED Controller. 911STROBE 14 LED Controller Installed

LED CONTROLLER BANKS

1 LR1, LR2, LR3, LR4 : ROOF STROBE LEFT

2 RR1, RR2, RR3, RR4 : ROOF STROBE RIGHT

3 LH1, LH2 : HEADLIGHT STROBE LEFT

4 RH1, RH2 : HEADLIGHT STROBE RIGHT

5 LBK, RBK : BRAKE LIGHTS

LED CONTROLLER CHANNELS

PWR 3.6-7.4VDC POWER INPUT

AUX THROTTLE SIGNAL INPUT USED TO SWITCH LBK & RBK LED CHANNELS DIM / FULL BRIGHT & AUXILIARY SIGNAL INPUT USED TO SWITCH POWER OR "LIGHTS" ON/OFF (top pin steering signal, bottom pin auxiliary signal)

LR1, LR2, LR3, LR4, RR1, RR2, RR3, RR4 CONSTANTLY DRIVE ANY SINGLE LED, ALL LEFT LED CHANNELS ARE THE SAME, AS ARE ALL RIGHT LED CHANNELS, THE RIGHT AND LEFT BANKS OF LEDs WILL STROBE BETWEEN ANOTHER UNLESS "LIGHTS" OR POWER IS SWITCHED OFF. STROBE RATE CAN BE ADJUSTED USING ADJUSTMENT POT P2. (LED BANK 1 & 2)

LH1, LH2, RH1, RH2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LEFT LED CHANNELS ARE THE SAME, AS ARE BOTH RIGHT LED CHANNELS, BOTH BANKS OF LEDs WILL BE CONSTANT ON UNLESS HEADLIGHT STROBE IS ACTIVATED ("LIGHTS" ARE ON, POWER IS ON, OR NO CH3 SIGNAL), IN WHICH CASE THE HEADLIGHTS WILL STROBE BETWEEN THE RIGHT AND LEFT BANKS. STROBE RATE CAN BE ADJUSTED USING ADJUSTMENT POT P1. (LED BANK 3 & 4)

LBK, RBK CONSTANTLY DRIVE ANY SINGLE LED, ALL LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL BE DIM UNLESS THROTTLE SIGNAL INDICATES BRAKES; IN WHICH CASE LEDs ARE FULL BRIGHT (LED BANK 5)

911STROBE 14 LED Controller RX Pass-Thru

LED CONTROLLER OPTION SELECTION DIP SWITCHES

BL BRAKE LIGHTS : Brake lights dim/full intensity at center-stick (choose if brake lights are on or off at idle)

RS ROOF STROBE : Single/double roof strobe (single or double flash)

TR THROTTLE REVERSE : Reverses the throttle signal input (if brake lights turn on with gas then flip this switch)

C3 CHANNEL 3 MODE : "Lights" or Power ON/OFF (Power turns everything on/off from auxiliary signal input, "Lights" toggles between standard vehicle lights and emergency strobes)

LED CONTROLLER ADJUSTMENT POTS

P1 HEAD RATE : Headlight strobe alternation speed

P2 ROOF RATE : Roof strobe alternation speed

PINOUT LEGEND

RESISTOR RESISTOR IN CIRCUITRY

CONNECTION ELECTRICALLY CONNECTED

IC INTEGRATED CIRCUIT

911STROBE 14 LED Controller

+ POSITIVE VOLTAGE FROM POWER SOURCE

- NEGATIVE GROUND FROM POWER SOURCE

R+ POSITIVE OUTPUT WITH INLINE RESISTOR

T- NEGATIVE BRAKE LIGHT OUTPUT (THROTTLE SIGNAL SWITCHED)

R- NEGATIVE ROOF STROBE OUTPUT (AUXILIARY SWITCHED)

H- NEGATIVE HEADLIGHT OUTPUT (AUXILIARY SWITCHED)

T THROTTLE SIGNAL INPUT

A AUXILIARY SIGNAL INPUT

TOP PINOUT

5055 Top Pinout 

BOTTOM PINOUT

5055 Bottom Pinout

WIRE COLOR (TO RX)

BLUE - POSITIVE (TOP PWR PIN ON LED CONTROLLER)
BLACK - GROUND (BOTTOM PWR PIN ON LED CONTROLLER)
WHITE - THROTTLE SIGNAL (BOTTOM AUX PIN ON LED CONTROLLER)
GREY - AUXILIARY SIGNAL (TOP AUX PIN ON LED CONTROLLER) 

WIRE COLOR (TO LEDs)

BLUE - POSITIVE
BLACK - GROUND