Телефон: +7 (937) 519-34-24

DOWNLOAD- PDF Tech Sheet

Use to connect up to 14 LEDs directly to the RX (receiver) using the included 2-Channel RX Plug with constant navigation, adjustable rate strobe lights, simulated rotating beacon, landing lights, and full TX/RX control built right in.

Pins can be soldered to for a hardwired connection. Pins can also be removed if they will not used.

Plug the NIGHTFLY™ 14 LED Controller into two available channels of the RX (tied to any 2-position switches on the TX) by plugging the 2-channel RX plug into either set of PWR & AUX channels on the LED controller with the rib UP.  Plug the connector with 3 wires on the other end into a RX channel to be used for switching power ON/OFF to the entire LED controller, and plug the connector with 1 wire into the second RX channel to be used for switching power ON/OFF to the Landing Lights.

If a separate power source (3.6-7.4VDC) will be used, follow these instructions.

Align BLUE wires with the top side of the NIGHTFLY™ 14 LED Controller. NIGHTFLY 14 LED Controller Installed

LED CONTROLLER BANKS

1 S1 1, S1 2 : ADJUSTABLE STROBE #1 (SINGLE FLASH)

2 S2 1, S2 2 : ADJUSTABLE STROBE #2 (SINGLE OR DOUBLE FLASH)

3 LL 1, LL 2, LL 3, LL 4 : LANDING LIGHTS (TX SWITCHABLE)

4 CN 1, CN 2, CN 3, CN 4 : CONSTANT NAVIGATION

5 RB 1, RB 2 : ROTATING BEACON (FAST OR SLOW)

LED CONTROLLER CHANNELS

PWR 3.6-7.4VDC POWER INPUT

AUX RX SIGNAL INPUT #1 USED TO SWITCH ALL LED CHANNELS ON/OFF & RX SIGNAL INPUT #2 USED TO SWITCH LANDING LIGHT LED CHANNELS ON/OFF (top pin landing lights signal, bottom pin power signal)

S1 1, S1 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL SINGLE STROBE AT THE RATE GIVEN BY ADJUSTMENT POT P1 (LED BANK 1)

S2 1, S2 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL SINGLE OR DOUBLE STROBE (OPTION SELECT DIP SWITCH S2) AT THE RATE GIVEN BY ADJUSTMENT POT P2 (LED BANK 2)

LL 1, LL 2, LL 3, LL 4 CONSTANTLY DRIVE ANY SINGLE LED, ALL LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL BE OFF UNLESS LANDING LIGHTS SIGNAL INDICATES ON; IN WHICH CASE LEDs ARE FULL BRIGHT (LED BANK 3)

CN 1, CN 2, CN 3, CN 4 CONSTANTLY DRIVE ANY SINGLE LED, ALL LED CHANNELS ARE EXACTLY THE SAME, CONSTANT ON (LED BANK 4)

RB 1, RB 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL SIMULATE A ROTATING BEACON. ROTATION RATE CAN BE ADJUSTED FAST/SLOW USING OPTION SELECT DIP SWITCH BR (LED BANK 5)

NIGHTFLY 14 LED Controller Power Plug

LED CONTROLLER OPTION SELECTION DIP SWITCHES

BR BEACON RATE : Fast/slow rotating beacon speed

S2 STROBE 2 : Single/double strobe output on STROBE #2

1R POWER REVERSE : Reverses the power signal input (flip to change which position of the TX switch is ON)

2R LANDING REVERSE : Reverses the landing light signal input (flip to change which position of the TX switch is ON)

LED CONTROLLER ADJUSTMENT POTS

P1 S1 RATE : STROBE #1 strobe speed

P2 S2 RATE : STROBE #2 strobe speed

PINOUT LEGEND

RESISTOR RESISTOR IN CIRCUITRY

CONNECTION ELECTRICALLY CONNECTED

IC INTEGRATED CIRCUIT

NIGHTFLY 14 LED Controller

+ POSITIVE VOLTAGE FROM POWER SOURCE

- NEGATIVE GROUND FROM POWER SOURCE

R+ POSITIVE OUTPUT WITH INLINE RESISTOR

S1- NEGATIVE STROBE 1 OUTPUT (IC SWITCHED)

S2- NEGATIVE STROBE 2 OUTPUT (IC SWITCHED)

2- NEGATIVE LANDING LIGHT OUTPUT (LANDING SIGNAL SWITCHED)

CN- NEGATIVE NAVIGATION OUTPUT (IC SWITCHED CONSTANT)

RB- NEGATIVE ROTATING BEACON OUTPUT (IC SWITCHED)

1 CONTROLLER POWER SIGNAL INPUT

2 LANDING LIGHT SIGNAL INPUT

TOP PINOUT

5056 Top Pinout 

BOTTOM PINOUT

5056 Bottom Pinout

WIRE COLOR (TO RX)

BLUE - POSITIVE (TOP PWR PIN ON LED CONTROLLER)
BLACK - GROUND (BOTTOM PWR PIN ON LED CONTROLLER)
WHITE - POWER SIGNAL (BOTTOM AUX PIN ON LED CONTROLLER)
GREY - LANDING SIGNAL (TOP AUX PIN ON LED CONTROLLER) 

WIRE COLOR (TO LEDs)

BLUE - POSITIVE
BLACK - GROUND