Телефон: +7 (937) 519-34-24

DOWNLOAD- PDF Tech Sheet

Use to connect up to 14 LEDs directly to the RX (receiver) using the included 2-Channel RX Plug with constant navigation, adjustable rate alternating single, double, triple, single/double, double/triple, or machine gun strobe lights, 1Hz single strobes, simulated rotating beacon, landing lights, and full TX/RX control built right in.

Pins can be soldered to for a hardwired connection. Pins can also be removed if they will not used.

Plug the NIGHTFLY2™ 14 LED Controller into two available channels of the RX (tied to any 2-position switches on the TX) by plugging the 2-channel RX plug into either set of PWR & AUX channels on the LED controller with the rib UP.  Plug the connector with 3 wires on the other end into a RX channel to be used for switching power ON/OFF to the entire LED controller, and plug the connector with 1 wire into the second RX channel to be used for switching power ON/OFF to the Machine Gun Strobes or Landing Lights.

If a separate power source (3.6-7.4VDC) will be used, follow these instructions.

Align BLUE wires with the top side of the NIGHTFLY2™ 14 LED Controller. NIGHTFLY2 14 LED Controller Installed

LED CONTROLLER BANKS

1 SL 1, SL 2 : ADJUSTABLE ALTERNATING STROBE LEFT (MULTIPLE PATTERNS)

2 SR 1, SR 2 : ADJUSTABLE ALTERNATING STROBE RIGHT (MULTIPLE PATTERNS)

3 LL 1, LL 2 : LANDING LIGHTS (TX SWITCHABLE)

4 SS 1, SS 2 : 1HZ SINGLE STROBE

5 CN 1, CN 2, CN 3, CN 4 : CONSTANT NAVIGATION

6 RB 1, RB 2 : ROTATING BEACON (FAST OR SLOW)

LED CONTROLLER CHANNELS

PWR 3.6-7.4VDC POWER INPUT

AUX RX SIGNAL INPUT #1 USED TO SWITCH POWER TO LED CHANNELS ON/OFF & RX SIGNAL INPUT #2 USED TO SWITCH MACHINE GUN STROBE OR LANDING LIGHT LED CHANNELS ON/OFF (top pin machine gun / landing lights signal, bottom pin power signal)

S1 1, S1 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL STROBE IN PATTERN DETERMINED BY P1 AND PHASE DETERMINED BY OPTION SELECT DIP SP, ALTERNATING WITH S2 1 & S2 2 AT THE RATE DETERMINED BY P2 (LED BANK 1)

S2 1, S2 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL STROBE IN PATTERN DETERMINED BY P1 AND PHASE DETERMINED BY OPTION SELECT DIP SP, ALTERNATING WITH S1 1 & S1 2 AT THE RATE DETERMINED BY P2 (LED BANK 2)

LL 1, LL 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL BE OFF UNLESS LANDING LIGHTS SIGNAL INDICATES ON; IN WHICH CASE LEDs ARE FULL BRIGHT. IF OPTION SELECT DIP C2 IS DISABLED BOTH LED CHANNELS WILL BEHAVE EXACTLY THE SAME AS S1 1 & S1 2 AND LANDING LIGHTS SIGNAL WILL SWITCH S1 1, S1 2, S2 1 & S2 2 ON/OFF. (LED BANK 3)

SS 1, SS 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL STROBE AT 1HZ UNLESS POWER SIGNAL INDICATES OFF.  IF OPTION SELECT DIP C2 IS DISABLED BOTH LED CHANNELS WILL BEHAVE EXACTLY THE SAME AS S2 1 & S2 2. (LED BANK 4)

CN 1, CN 2, CN 3, CN 4 CONSTANTLY DRIVE ANY SINGLE LED, ALL LED CHANNELS ARE EXACTLY THE SAME, CONSTANT ON UNLESS POWER SIGNAL INDICATES OFF. (LED BANK 5)

RB 1, RB 2 CONSTANTLY DRIVE ANY SINGLE LED, BOTH LED CHANNELS ARE EXACTLY THE SAME, LEDs WILL SIMULATE A ROTATING BEACON. ROTATION RATE CAN BE ADJUSTED FAST/SLOW USING OPTION SELECT DIP SWITCH BR. (LED BANK 6)

NIGHTFLY2 14 LED Controller 2 Channel RX Power Plug

LED CONTROLLER OPTION SELECTION DIP SWITCHES

BR BEACON RATE : Fast/slow rotating beacon speed

SP STROBE PHASE : Long/short interval between alternating strobe flashes in multi-flash patterns

CM CHANNEL MODE : Single or multi-mode channel inputs (simple on/off, or nav/nav-beacon/nav-beacon-strobes/nav-beacon-strobes-landing/all on/off)

C2 CHANNEL 2 : Enable/disable landing lights & single strobe; channel 2 switches landing lights or alternating strobes on/off

LED CONTROLLER ADJUSTMENT POTS

P1 STROBE MODE : Alternating strobe single, double, triple, single/double, double/triple, or machine gun patterns with phase set by option select DIP SP

P2 STROBE RATE : Rate that alternating strobe alternates between SL 1, SL 2 and SR 1, SR 2

PINOUT LEGEND

RESISTOR RESISTOR IN CIRCUITRY

CONNECTION ELECTRICALLY CONNECTED

IC INTEGRATED CIRCUIT

NIGHTFLY2 14 LED Controller

+ POSITIVE VOLTAGE FROM POWER SOURCE

- NEGATIVE GROUND FROM POWER SOURCE

R+ POSITIVE OUTPUT WITH INLINE RESISTOR

SL- NEGATIVE STROBE LEFT OUTPUT (IC SWITCHED)

SR- NEGATIVE STROBE RIGHT OUTPUT (IC SWITCHED)

2- NEGATIVE LANDING LIGHT OUTPUT (LANDING SIGNAL SWITCHED)

SS- NEGATIVE 1HZ SINGLE STROBE OUTPUT (IC SWITCHED)

CN- NEGATIVE NAVIGATION OUTPUT (IC SWITCHED CONSTANT)

RB- NEGATIVE ROTATING BEACON OUTPUT (IC SWITCHED)

1 CONTROLLER POWER SIGNAL INPUT

2 LANDING LIGHT SIGNAL INPUT

TOP PINOUT

5057 Top Pinout 

BOTTOM PINOUT

5057 Bottom Pinout

WIRE COLOR (TO RX)

BLUE - POSITIVE (TOP PWR PIN ON LED CONTROLLER)
BLACK - GROUND (BOTTOM PWR PIN ON LED CONTROLLER)
WHITE - POWER SIGNAL (BOTTOM AUX PIN ON LED CONTROLLER)
GREY - LANDING SIGNAL (TOP AUX PIN ON LED CONTROLLER) 

WIRE COLOR (TO LEDs)

BLUE - POSITIVE
BLACK - GROUND